Overclocking software amd sempron

In the OC-database you can see over thousands of overclockers with their systems to get an overview what you may reach with this processor. More exactly, there is a system bus which has the double value of the FSB, but to avoid confusions, we belong to the FSB. How you can see at the rating, not only the processor speed is important for a good overclocked CPU, it is the best combination of FSB and multiplier.

These two combinations we like to find out in the following progress of this guide and set them to the highest values. At this point it will be exciting because it depends on the used mainboard and the used CPU if we can change the multiplier. We have a processor which is manufactured before the week 43 of the year look at the picture , or we have an AMD Mobile CPU because there is the multiplier changeable. In this case we only have to unlock the multi by closing the L3 and L1 bridges see painting guides in the workshop , or with a fine wire in the CPU socket interactive pinmod guide.

Now we know how to change the multiplier but before we go on with the overclocking we have to find out the highest FSB.

If you can change the multiplier, set it to the lowest value to prevent that we reach the maximum of the CPU. So it would be good to set the memory timings also to the lowest vlaue, too e. Those who have a Mhz FSB CPU and uses memory which has Mhz or Mhz can try to go to the next higher stage or if the memory is very slow, try to set them asynchronus to a higher value. We can overclock graphic card later and the pci-bus should not be much higher than the standard settings, because it would overclock the sound card, TV card, etc.

Read more in the manual of your mainboard. If you find out the highest FSB and the PC boots with these settings, we can go on to increase the memory frequency in small steps. But Attention! If you increase the memory too much, you may loose your harddisk data or get crashed hdd data. If the maximum FSB is reached we can go on with the processor overclocking. I repeat that the processor has to be cooled very good and the higher frequency will also increase the temperature.

So please watch the temperature! If you make the pinmod or paint the multiplier on the CPU, do not forget to install the cooler. It may be troublesome for a few of you but if you so not install the cooler, the CPU will die within seconds — believe me. Now set the multiplier step by step higher and look if the PC starts normally. If the end point of the CPU is reached which can be detected with a defective start or windows bluescreen, we can try to set the CPU to this or higher value and make it stable.

First step for better stability is a higher Vcore CPU voltage. You should increase the Vcore only in small steps because the temperature will jump up and may damage transistors inside of the CPU — this could be the end for the processor. In most cases we are now at 1,85V real 1,90V but only increase the Vcore as much as necessary to run it stable.

Do not set it to the highest voltage without trying the lower voltages! However, you can also install an SSD for better performance. Now, as the software has completed all the test, you have the base score and have understood how things work now, it is time to overclock your graphics card. Following is the image of the settings, and they ensure you get the highest clock speed while staying within a safe temperature range. Now, as you have the optimal MSI Afterburner settings, firstly move the core clock slider to the right.

Run heaven benchmark 4. Now go through the 26 screens and wait for the test results to come up. Now you will notice that your score improves from the last time. The first test improved our average frame and tested score slightly. Now you will see an improvement and notice a degree increase in temperature during the trial. For this open MSI Afterburner and reduce speed by This is the optimal clock speed. Disclaimer: Please do all of the above steps on your own risk. Overclocking can sometimes be dangerous, and it can also cause harm to your graphics card.

Only continue if you know what you are doing. Overclocking is finally completed, you can repeat the steps for memory clock as well. I hope you enjoyed learning to overclock your graphics card. Once overlocking is completed, click on the save icon on MSI Afterburner and then click on a number to assign it the particular slot to save settings. To have better performance, while playing your favorite games, you can load up these settings.

You will find better performance in games with the new overclocked graphics card. Some games, however, might not work and may note some graphical glitches. When something like this happens, click on the reset button and go back to the default settings.

Contents What is Overclocking? These are as followed: Software that can be used to set new speeds for your GPU. A program that can stress test your system to make sure you have stable settings GPU temperature is essential, and for that, you need to download an optional third program for it.

You can download GPU temp, for extra temperature and voltage monitor. The details for each are as below: Amd Radeon Overclocking Software Core clock speed- the main speed that you are going to overclock. Memory Clock Speed- this is going to be overclocked but only after testing the core clock. Control Panel- used to overclock your core clock, memory clock, and fan speed. The temperature of GPU. In the first step, install the Unigine Heaven stress testing software From the start, menu run heaven benchmark 4.

Take note of the following things: Score at the end of the test Higher is better. FPS at the end of the test Higher is better. The temperature during the test. Lower is better. In the first step, go to MSI Afterburner and click on the settings icon. Restart your PC within a second. Bookmark this page, to come back here again Click on the general tab in Afterburner Tick the unlock voltage control, unlock voltage monitoring, and force constant voltage.

Click on the OK button after applying the above settings You will be asked to restart your computer, click on the ok button. Now, you can see that your power limit goes up.

Put the core voltage to the slider to the right, and the percentage you get will be dependent on your graphics card. Click the check button present beneath the slider. To further play around with the performance, follow the below settings : Add additional to your clock speed Run again the heaven benchmark 4.